Mitra Hazard adalah distributor produk electrical equipment explosion proof dari beberapa produsen ternama dari negara-negara Eropa dan Amerika, diantaranya Emerson-Appleton, ATEX Delvalle, dan TEPEx. Seluruh produk telah mengantongi izin dan sertifikat berstandar explosion proof dari ATEx, IECEx, CE, dan sebagainya. Tersedia produk berstandar explosion proof seperti lampu explosion proof (tube light, flood light, high bay, dan sebagainya) box empty enclosure, box control station, junction box, terminal box, dan produk cable gland dan pipe fitting, mulai dari non armoured, armoured. Mitra Hazard juga mendukung pengiriman ke seluruh Indonesia, terutama wilayah Jakarta, Bogor, Depok, Tangerang, Bekasi, Cilegon, Serang, Rangkas Bitung, Karawang, Cikarang.
TXTM SWE Series 16/20 Amp Switches, Circuit Breakers, and “Break Glass” Call Points
Applications
- Designed to prevent operation in explosive atmospheres during connect and disconnect operation of lighting and light power loads.
- For use in hazardous areas where ignitable vapors, gases or highly combustible dusts are present.
- For installation in chemical and petrochemical plants, refineries and other process industries.
Features
Available up to 690 Volts, and up to 20 Amps
- 16 Amp version:
- Two bottom M20 clearance holes.
- Switch mechanism fixed at the bottom of the box.
- Termination:
- Type 1: 2.5 mm2 (0.004 in2)
- Type 2: 2.5 mm2 (0.004 in2) flexible, 4 mm2 (0.006 in2) solid
- Internal earth:
- 2 x 2.5 mm2 (0.004 in2) terminals
- Supplied with:
- 1 x white self-adhesive laminated plastic label with black lettering – 58 mm x 18 mm (2.28” x 0.71”)
- 20 Amp version:
- Two M20 threaded entries on the bottom of the box.
- Switch mechanism fixed on the bottom of the box.
- Padlockable handle in position 0 using maximum 4 padlocks
- maximum handle diameter 8 mm (0.315”) and minimum 15 mm (0.59”) length.
- Termination:
- 2.5 mm2 (0.004 in2) flexible/4 mm2 (0.006 in2) solid
- Internal earth:
- 2 x 4 mm2 (0.006 in2) terminals
- Supplied with:
- 1 x yellow self-adhesive laminated plastic label with black lettering – 65 mm x 18 mm (2.56” x 0.71”)
Related products
ECOM Tab-Ex® 03 D2 – Next Generation 8″ (20.3 cm) Android™ Tablet for Division 2
ECOM Pad-Ex® 01 P8 DZ2 – Windows Tablet (Zone 2/22 & Division 2)
HOFFMAN Corrosion Inhibitor
Use Corrosion Inhibitors to protect electronic components inside the enclosure against corrosion. It is simple and economical to use; no surface preparation is required and puts protected equipment to use immediately without degreasing or coating removal. Each inhibitor contains a special chemical combination that vaporizes and condenses on all surfaces in an enclosed area. Vapors will redeposit as needed in the event of condensation of moisture on surfaces. These vapors reach every part of an enclosure, protecting all interior components. They do not interfere with electrical, optical or mechanical surface properties. Protection is effective even in salt-water atmospheres. The AHCI5E and AHCI10E emitters have additional red-metal inhibitors for further protection. The normal useful life-span of Hoffman corrosion inhibitors is in excess of one year. However, inhibitor life expectancy is shortened by approximately 25 percent when exposed to temperatures above 104 F (40 C). This product is not recommended for use where temperature exceeds 199 F. Since Corrosion Inhibitors are vapor-phase protective, all surfaces to be protected should be accessible to the vapors. The maximum distance the vapors can travel is approximately 1.50 ft. (.46 m). Protection of long, narrow enclosures can be achieved with tape or multiple inhibitors. Each Corrosion Inhibitor is individually packaged in a resealable bag for maximum effectiveness at the time of usage. Corrosion inhibitors should be stored at temperatures not exceeding 120 F (45 C ). Hoffman corrosion inhibitors are not returnable. When determining the proper corrosion inhibitor for your application, assume the enclosure volume to be protected is greater than calculated if (1) cabinet doors are opened frequently, (2) cabinet is located in an extremely corrosive area and/or (3) cabinet length divided by depth is greater than four.
The normal useful life-span of HOFFMAN corrosion inhibitors is in excess of one year. However, inhibitor life expectancy is shortened by approximately 25 percent when exposed to temperatures above 104 F (40 C). This product is not recommended for use where temperature exceeds 199 F. Since HOFFMAN corrosion inhibitors are vapor-phase protective, all surfaces to be protected should be accessible to the vapors. The maximum distance the vapors can travel is approximately 1.50 ft. (.46 m). Protection of long, narrow enclosures can be achieved with tape or multiple inhibitors.
Each nVent HOFFMAN corrosion inhibitor is individually packaged in a resealable bag for maximum effectiveness at the time of usage. Corrosion inhibitors should be stored at temperatures not exceeding 120 F (45 C ). HOFFMAN corrosion inhibitors are not returnable. When determining the proper corrosion inhibitor for your application, assume the enclosure volume to be protected is greater than calculated if (1) cabinet doors are opened frequently, (2) cabinet is located in an extremely corrosive area and/or (3) cabinet length divided by depth is greater than four.
Reviews
There are no reviews yet.